85 dBA or less Enclosures

678 Enclosure with hinged removable doors on front and back.  Removable doors on ends.  Enclosure has custom paint.  Unit encloses a Roots 711 URAI with 60 HP motor.  Enclosure is shipped with an integral sub-base and is completely assembled to minimize field installation.  Acoustic Enclosure Assembly, 72\" LG X 40\" W X 60\" HT, 14 GA Galvanized Skin, 2\" Thick 8lb/ft3 Mineral Wool insulation, 4 Removable Doors, Removable Roof, Ships fully assembled. Enclosure achieves at least 12 dBA noise reduction at 3'
Galvanized Enclosure used on a vacuum system.  Hinged removable doors. Galvanized acoustical enclosure used on a pressure system with the inlet filter mounted on the exterior of the package. This is a weather - acoustical enclosure featuring 14 ga galvanized steel skin, 2\" thick 8 lb/ft3 rock wool acoustical material, 6 hinged and removable doors and a ventilation fan on a thermostat.  Enclosure has external dimensions of 114\" Long x 56\" Wide x 112\" Tall.  Enclosure was shipped fully assembled.
This is an interior shot of the 112\" Long x 56\" Wide x 112\" Tall enclosure showing the acoustical material mechanically fastened to the walls.  Steel studs are shot onto the wall to maintain an excellent mechanical adhesion for the acoustic material.  This enclosure does not have any additional finishes to the acoustic material.  Perforated material can be applied over the acoustic material for superior mechanical protection. EN174B00H1 with open side doors. Note that the center post is removable to give even greater access. EN174B00H1 Discharge baffles provide an exhaust point on the enclosure ventilation fan.  The louvered exhaust provides for reduction of the transmitted noise.  Air is pulled in around intake vents under the roof.
Weather and noise blower enclosure assembly.  The enclosure is 76.5\" Long x 47\" Wide x 59.5\" Tall.  This enclosure includes the use of a 120 Volt1170 CFM ventilator controlled on a thermostat.  This enclosure is ideally suited for use with our VersaBase 567 bases utilizing 4\" and smaller silencers. Noise reducing weather resistant acoustical enclosure. The enclosure measures 59\" Long x 34.5\" Wide x 48\" Tall.  It features four (4) removable doors by simply turning quarter turn fasteners.  A 1170 cfm ventilator is provided to dissipate heat from the installed equipment. Noise reducing acoustical weather enclosure that measures 59\" Long x 34.5\" Wide x 48\" Tall.  This photo illustrates how easy it is to service the equipment located within the enclosure.
Noise reduction and weather enclosure designed for maximum silencing. The enclosure is show without its roof or door in place.  Four inches of attenuation material is used for maximum attenuation.  A special subbase was designed for the discharge of the cooling area to minimize transmitted sound.  The enclosure is 76.5\" Long x 47\" Wide x 59.5\" tall.  An actual noise reduction of over 20 dBA at 3' was achieved with this design. Image shows the attenuation material mounted on the roof.  The attenuation is held in place by welded pins and a perforated protective sheet.  Positive mechanical fastening is essential to prevent sagging of the attenuation material. Standard Enclosure for VB567
Large VB567 Enclosure suitable for 5\" Silencers, Corner View, two doors off Large VB567 Enclosure suitable for 5\" Silencers.
Click for full size image
678 Enclosure with hinged removable doors on front and back. Removable doors on ends. Enclosure has custom paint. Unit encloses a Roots 711 URAI with 60 HP motor. Enclosure is shipped with an integral sub-base and is completely assembled to minimize field installation.

85 dBA or less Enclosures



Various enclosure that show case many of the features available. Enclosures are available to achieve 85 dBA or less at 3' from the equipment.


< Back to photo gallery